Perpetual Motion Automotive Motor

Votes: 0
Views: 138
Previous Next

Perpetual Motion Automotive Motor ( A "zero emission vehicle" )
https://www.designdeskinc.com/perpetual-motion-automotive-motor.html

In the years and decades to come oil will become exceedingly expensive as the oil was not grown for industrial use but rather harvested from earth's deposits. The following design system is a "draft accelerator" perpetual motion "Active" electric power plant using two types of pressure to then "continually" produce electricity for an electric automobile. The system uses hydraulic fluid ( silicone oil ) and pneumatic ( "air" ) pressure to motivate the power plant. It is important to understand the system does not burn the oil. The system replaces the air pressure automatically.The design cycles hydraulic pressure to produce electricity. It does not burn the oil. The "working fluid" then a "non electrically conductive" - "non flammable oil" being Siloxane (silicone oil). The design then will allow for an unlimited range electric vehicle with "on demand" service(* no battery required ! ).

Parts List

1. Drive shaft cup

2. Automotive automatic transmission rotated by number 55

3. Pulley and drive belt system causes rotation for numbers 5, 7 ,8, 9, rotational input torque by
pulley upon extending drive shaft from number 55 tandem rotation with the armature of number 55.

4. Drive belt

5. Air pump ( contains electric clutch)

6. Air filter

7. Power steering pump / and power break pump

8. Air conditioner compressor ( contains electric clutch)

9. 12v alternator

10. Torque converter

11. A "throttle ( potentiometer / variable resistor

12. Electric motor

13. Hydraulic pump

14. Logic processing "systems mapping"

15. R.P.M. sensor

16. A "counter tilt" electric motor

17. Ratio gear set ratio at 1:10

18. Pneumatic impeller

19. Exhaust air filter
20. Pneumatic flow pipe coupling

21. Pulley 4" dia ( diameter)

22. Drive belt

23. Counter tilt electric motor variable resistor / circuit controlled potentiometer

24. Voltage regulator

25. Tension pulley

26. Pneumatic impeller

27. Magneto -

28. Main high voltage generator

29. Hydraulic impeller

30. Oil flow rate regulator valve - redundant solenoid control -

31. Dual component pressure storage tank
32. Oil drain

33. One way valve ( oil / hydraulic fluid )

34. Oil filter

35. Oil return coupling

36. One way valve
37. Pneumatic pressure pipe / tubing / hose

38. Pneumatic fitting

39. Pneumatic "Start valve"

40. Circuit controlled variable resistor / “circuit” controlled potentiometer

41. Solenoid

42. Plasma box electrical ground)

43. Potentiometer / variable resistor

44. Large pulley 12"dia (diameter)

45. Pneumatic return coupling / pipe fitting

46. Flow system shut off valve

47. Oil flow pipe

48. Pneumatic “high” pressure flow pipe / pressure hose

49. Over pressure max pressure system safety

50. Pneumatic pressure sensor
51. Multi wire "ribbon wire" bus connector wire connector instrumentation wire connector

52. Plasma box electrical ground)

53. Manual pneumatic fill valve oneway fill valve

54. Oil fill pressure cap

55. Main electric automotive

Voting

Learn how to vote for your favorites.

  • ABOUT THE ENTRANT

  • Name:
    Eric Crews
  • Type of entry:
    individual
  • Profession:
    Engineer/Designer
  • Number of times previously entering contest:
    4
  • Eric's favorite design and analysis tools:
    I LIKE AUTO CAD AND MY DRAFTING BOARD
  • Eric's hobbies and activities:
    MACHINE DESIGN
  • Eric belongs to these online communities:
    FACEBOOK
  • Eric is inspired by:
    SEEING THE CONDITIONS IN CURRENT SITUATIONS REGARDING THE FAILURES OF UTILITY COMPANIES TO MAINTAIN A COST EFFECTIVE SOURCE OF POWER FOR PEOPLE. THE INCLEMENT WEATHER CAUSING POWER OUTAGES ENDANGERS PEOPLE SO WE HAVE ADDRESSED THIS PRODUCING DESIGNS THAT REQUIRE NO FUEL OR ENVIRONMENTAL ENERGY INPUT. IE SOLAR POWER/ HYDRO ETC.
  • Patent status:
    pending